Author: Diana Hicks

How to pump a longboard?

You can move your longboard quickly on flat ground or even uphill by pumping it instead of kicking it. This works for both short and long distances. It involves moving your body back and forth and shifting your weight in a way that makes your longboard make quick, small turns, gaining speed by using centripetal forces without your feet ever touching the ground.

What is longboard pumping?

Pumping a longboard is its own subculture. Pumpers are a dedicated group who share their experiences and knowledge with each other all the time. So why is everyone making a big deal about longboard pumping?

Most people who start longboarding start by pushing to get their board moving. They usually keep pushing for the rest of their longboarding lives, like when they want to go cruising. Most longboarders also use gravity to move quickly when they are going downhill.

Another way to do it

Pumping, or “skumping” (which is a combination of skating and pumping), is another way to move forward on your longboard. You use your body weight as a propelling engine by making swerving movements in time with each other. By shifting your weight slightly from left to right at the right times, you can make small zigzags on your longboard to gain momentum and speed.

The move is similar to “tic-tac,” which is when you speed up on a skateboard by slightly lifting your front wheels off the ground (by pressing down on the tail) and swinging the front of your board left and right (making a “tic-tac” sound).

Even though your wheels don’t leave the ground when you pump, your body moves in a similar way.

How to pump a longboard?

It’s no secret that you have to practice, practice, and practice to learn how to pump on your longboard. After 15 or 20 miles of riding, many longboarders start to get a feel for how to do it right.

Depending on how often and how well you ride, it could take weeks of practice and building the right muscles before you can really get your longboard to pump. This is especially true if you are using a typical beginner board, which is a drop deck board that is on the longer side and has trucks that both turn the same way. See the section below about pumping setups.

Even though learning to pump can be hard because you’re trying to find the right motion, once you do, you should be able to pump for miles without much trouble as long as you’re fit enough to walk 5 miles without getting tired.

Here is a list of steps from another famous pumper, John Gilmour, that might help you learn faster:

If you have access to a regular skateboard, you can start by learning to “tic-tac” on it by using the kicktail to lift your front wheels slightly and moving your board’s nose left and right with your front foot to gain speed. Tic-tac-toe will help you get used to the back arm motion and twisting of the torso that are needed to speed up.

Once you’re good at tic-tac-toe, you should get a short longboard with very loose and turny trucks (like Seismic trucks) and soft bushings. Regular trucks with hard bushings would make it impossible for you to learn the technique.

Start pumping on a surface that is very easy to grip (no slippery spots). Give your board a small push to get it moving, and then turn it by pressing hard on your rail with your front foot to make your trucks turn while pushing back laterally with your back foot. Keep practicing turning left and right, like tic-tac-toe, but without lifting your front wheels.

If your longboard doesn’t pick up speed when you make these turns, you probably haven’t figured out the right timing yet. If so, try going up a small hill that isn’t too steep for your board to roll by itself. Try the pumping carves on it again. If your board moves, you’re getting better at pumping.

Once you can keep going just by pumping on a very gentle slope, it’s time to go back to flat ground and practice your carves until you can keep the longboard going without stopping. After a while, you might even try pumping a little uphill, but that might be hard on a regular longboard. Again, see the setup section for more information.

If you still can’t keep going on your longboard by doing these carves, try pumping around in a big circle, always in the same direction, to practice carving on one side. Since you’ll be making a lot of turns, make sure you do it on a surface with a lot of grip. When you’re pumping in circles, it will be easier for you to circle on the front side, which you can do by doing toeside carves. If you’re a regular footer, this means you should ride in a circle going clockwise. If you’re a goofball, you should ride counterclockwise. Each time you carve, the hard pressure you put on your front rail combines with the turning force to speed your board up.

You could also find a longboard with a big, flexible deck to help you learn how to pump. The bouncing will help your pumping, but you will lose more energy and speed because of the momentum of the vertical bouncing.

Last word

If you’re new to pumping on a longboard, this is a whole new world to explore. Pumping was a big surprise to me, and ever since I learned how to do it, it has been my main focus when longboarding.

Getting into longboard pumping doesn’t mean you can’t do other types of riding as well. For example, many long distance skaters combine pushing and pumping to get the longest and most efficient rides. Specialized brands like Gbomb make longboards that are good for both styles.

On a pintail cruiser or a kicktailed street hybrid, with the right setup, you can combine pumping and carving with cruising or freestyling. Or, you could decide to ride a surfskate on the boardwalk and maybe change the bushings to make it a better long-distance rider.

Overall, the turny trucks, the deck flex, and the soft wheels are the keys to pumping. And, of course, the right rhythm and way to move your body. Check out this Facebook group to learn more about the world of pumping.

What Is A Quantum Dot Display

When the market is flooded with terms like UHD, HDR, FPS, and LCD, it can be difficult to keep up. It’s important to learn about the various technologies and how they affect the quality of the monitor before purchasing one. Since the turn of the century, another display technology has emerged. Quantum dot technology is the solution to this problem.

To learn more about quantum dot technology, keep reading. ViewSonic ELITE monitors with QLED capability are another option.

Understanding what a light-emitting diode (LED) is can help us grasp quantum dot technology. When an electric current is passed through it, it produces light. Light emitting diode (LED) displays are LCD models with LED illumination that produce darker blacks and more vibrant colors. But LED lights aren’t inherently white. White light is produced by applying a yellow phosphor to blue LEDs.

However, how does this apply to quantum dot displays?


What is Quantum Dot Technology?


Quantum-dot screens, also known as QLED (Quantum dot LED), are essentially a new sort of LED-backlit LCD. In order for these panels to respond to light and electricity, they make use of extremely small phosphorescent crystals. The “nanoparticles,” which have a size of less than 500 nanometers, have the ability to glow in a variety of colors, each of which is precisely specified by the amount of atoms contained within. And instead of using backlights that are a pure white color, the quantum dots, when struck by blue light, emit either red or green light. This implies that the colors you see will be significantly more realistic and highly saturated than what you would see on an average LED panel.


How Does Quantum Dot Work?


Every pixel on the screen can produce either red, green, or blue light, and in certain cases a mixture of all three colors. Wavelengths are what determine how accurate the color of each pixel is going to be. Quantum dots may also be easily adjusted to their predetermined size in order to emit light of a variety of different wavelengths, which results in superior color generation.

Quantum dots are often arranged in a film, although they can also be contained in tubes. Tubes are the less popular option. The sheet is then positioned between a blue LED unit and color liquid crystal display (LCD) filters before being inserted. When the quantum dots are illuminated by the blue LED, they begin to glow in a red and green color. When these three colors are mixed together, they generate the “purest” kind of white light. The white light provides the color filters with a source that is more precise, which enables them to efficiently and precisely filter out the three hues.

The placement of the quantum dots in a QLED display is depicted in the diagram that can be found above. Gradations of red, green, and blue are produced as a result of light emitted from a blue LED light source that then travels through a film enhancement layer. After passing through the liquid crystal display panel (LCD) and the color filter glass, the various colors of light arrive at the screen, where they are used to produce an image.

Advantages of Quantum Dot Technology

The added quantum-dot layer brings your monitor a whole host of benefits.

Precise Color and Higher Peak Brightness


Since the quantum dots can be made to emit a specific quantity of light, this indicates that the color that is created will be more true to life. The nanoparticles have the ability to render colors across a wider spectrum at the highest possible brightness without sacrificing saturation. This makes it possible for photos to be displayed clearly even in extremely well-lit rooms. In addition, brightness is an essential component of a high dynamic range (HDR) experience, as it ensures that all of the nuances of light and color depicted onscreen appear more accurate to real life.


Better Energy Efficiency

Quantum dots only require a small amount of energy to work, and this can be achieved by a single blue light. In fact, they can produce a 30 percent increase in brightness while using about 30 to 50 percent less power. This reduced power consumption results in lower costs. Unlike conventional LCDs that waste energy combining and balancing different colors, QLED screens emit precise colors for improved energy efficiency.

Longer Lifespan and Low Burn-In

As QLED displays are based on existing LCD technology, they benefit from having a longer lifespan as they rely on modern and energy-efficient backlighting. Quantum dot technology also does not degrade over time, meaning QLED displays are less prone to burn-in. Burn-in is when part of an image will appear like a “ghost” on the screen and would not go away. This only happens when each self-lighting pixel dims over time.


Versatile Sizes and Thinner Panels

Since quantum dot technology is easier and less expensive to produce, QLED displays can be made in a greater range of sizes and can go as large as 98 inches. They can also be applied on large, thin, and flexible LCD panels, making the QLEDs easy to transport and install.

QLED vs OLED: What’s the Difference?


Organic light-emitting diode, often known as OLED, is most likely another type of display technology that you are familiar with. Organic light-emitting diodes, or OLEDs, are made up of organic molecules that light up when electricity is applied. Electroluminescence is the term used to describe this phenomena.

The operation of an OLED display is depicted in the diagram that follows. The positively charged anode layer is placed on top of the negatively charged cathode layer, creating a sandwich that contains the organic emissive layers. In order to generate colored light, an electric current will move through each layer, beginning at the cathode and ending at the color filter.

Every pixel in an OLED display is its own source of light, in contrast to a QLED, which relies on backlights. Due to the fact that they degrade more quickly, the organic materials that make up an OLED panel often have a higher production cost and a shorter shelf life. The self-emitting pixels of an OLED do not generate the same level of brightness as those of a QLED, but they are capable of projecting the darkest black, which results in deeper contrasts. When it comes to image preservation, OLEDs are far more prone to burn-in than other types of screens. However, it is essential to keep in mind that in addition to providing excellent viewing angles, rapid response times, and colors that are nearly perfect, OLED displays also offer.

Are QLED Monitors Any Good For Gaming?


Televisions are the most common type of display that utilize quantum dot technology. However, the capabilities of a QLED can also be translated onto a monitor, making it an excellent choice for use in gaming due to its versatility. Players prefer to compete using gaming displays that are able to create a more immersive viewing experience, and this is especially true in the realm of esports. The picture quality of games created with quantum dot technology is far more lifelike, with colors that are more bright and contrast that is more pronounced.

In the event that the gamer has to activate HDR video, QLEDs provide darker blacks, a wider color gamut, and more brightness than a standard panel would. And due to the additional capabilities that QLED monitors are equipped with, such as sync technology and black level stabilization, they frequently give superior technical performance than televisions. This enables players to breeze through graphically demanding games while still being able to see each and every piece in mesmerizing detail.

Final Thoughts


There is little doubt that quantum dot displays offer vivid colors and a host of other advantages. Gamers may find quantum dot screens to be a cinematic improvement over current flat-panel displays. Note that quantum dot displays are always being improved to deliver environmental-friendly displays with greater color performance, higher brightness and potentially even lower pricing to the market. This means that QLED gaming displays will soon be the norm for all gamers.

Visit our comprehensive guide to gaming monitors to discover more about their features and benefits. ViewSonic ELITE’s gaming-specific monitor lineup is also available for your perusal.

See more :


Best 29-Inch Monitors

How to Soundproof a Car

Sound that you don’t want can be annoying. Noise is annoying and makes it hard to focus. Road noise, like screeching tires, wind, engines, loud music from other cars or stalls, fans, etc., can ruin a good drive. Noise could come from either the outside or the inside. Radiations and vibrations from the engine cause windows and doors to rattle, and gaps like door seals and rain gutters let the outside noise in. But it’s sad that noise is everywhere and hard to get away from.

You don’t have to buy a new car if the noise is too much for you. Instead of paying for everything, you could try soundproofing.

Soundproofing is the process of putting barriers between noise and places where you don’t want it to get in. Noise is stopped by soundproofing, which works by absorbing sound waves to a certain degree.

Some lucky people get their cars from the factory with soundproofing, while others don’t.

Why soundproofing is important

It cuts down on all the outside noise.

It makes driving safer.

It makes you feel more at ease.

It makes the sound in your car better.

How do you make your car less noisy?

1.Put down soundproofing mats in your car

It’s hard to believe that a car’s floor isn’t as thick as one might think. Since the floor is close to the ground, it is easy for road noise to get into the car through it.

Normal floor mats catch dust, make the car more comfortable, and make it look better. They don’t help much with soundproofing, though, because they’re thin and not made for soundproofing. On the other hand, dampening/sound deadening mats are thick and last a long time to absorb noise, which makes the undercarriage quieter.

Also, keep in mind that installing the mats is different for each product. Some need to be cut before they can be put in place, while others are already cut.

You don’t need to get rid of your old mats. You can put them on top of the mats that stop noise. Check out the Noico car sound deadening mat, which is one of our best picks.

2.Add insulation to the liner

When used with mats that reduce noise, liner insulation cuts down on a lot of noise. Install the sound-dampening mats first, and then put the liner insulation right on top of the mats.

Even though it is a great way to block out noise, it is also used to keep heat in. It blocks noise by reflecting and absorbing vibrations from the source of the noise. Check out Kilmat for noise insulation, damping, sound deadener, etc. for your car.

3.Replace the rubber seals on the roof, windows, and doors.

Most door interiors are thin and empty, so it would be easy for the noise to get through (without the door handles, windows, and locks). Also, the doors of many older car models, especially, have little or no insulation. One good way to block out noise is to replace the rubber seals. In this case, too, using materials that reduce noise is the same as using insulation.

Also, the noise would get in through the cracks in your windows and doors. When the gaps are sealed, the noise will be less.

Use the material that blocks out noise on the roof as well. Please be careful when removing the cloth headliner, as it will need to be put back on after installation. Next, measure the roof and put the soundproofing material on it. Before you put insulation on your roof, you should wipe it down with alcohol on a clean cloth to get rid of any dirt. This also makes it stick better.

I would suggest using a peel-and-stick backing to insulate if you want it to be easy to use.

Get a kit that has everything you need in it so that installation is easy.

4.Check the tires for uneven wear and replace them if necessary.

If your car is making a lot of noise, it could be because of the tires you drive on every day. Riding on worn-out or uneven tears could be dangerous because they don’t hold the asphalt firmly, which could cause you to lose control of your car.

Small stones sometimes get stuck in your treads and hurt them. This makes the treads uneven, which makes them shake and make noise. Tires that aren’t aligned properly or aren’t very good also add to the noise.

To stop the noise, people should check their tires and replace them often.

When choosing tires for soundproofing, there are a few things to keep in mind:

Choose the wheels for your car that are the narrowest to cut down on noise. This is because wider wheels make more contact with the road, causing more vibrations to be picked up by your tires, which makes more noise.

Choose more rubber or bigger tires. Rubber is a sound absorber and acts as a cushion between your car and the road, so the more rubber there is, the less likely it is that the noise will get worse.


Tires with a decibel number and a three-wave symbol make less noise (noise rating). The decibel rating shows how many decibels were used to test the tires. The more decibels used, the better the tires. On the other hand, with the three-wave symbol, a line means less noise and great performance, while three waves mean more noise and low performance.

5.Adding an undercoat to reduce noise

Putting rubber on the car’s underside keeps it from rusting. Even though it is resistant to sand, water, salt, and chemicals, it also absorbs road and engine noise.

Most of it comes in spray cans, which makes it easy to use. You just have to spray it on the area you want to separate and let it dry.

6.Use soundproofing sprays in your car

These are made to be used in hard-to-reach places. They would be the right solution if, after installing liner insulation and deadening mats, there were still gaps.

The sprays are easy to use because they come in aerosol cans.

They could also come in professional cans that you use with paint guns and compressors.

7.Make sounds in the background

Adding soundproofing to your car makes it sound better. So, the best way to fight noise is to make more noise. That means turning up the background music to drown out the noise of the road. By putting in new sound systems, you can do this.

It makes things more fun, but it is dangerous.

8.Get rid of things that move.

Make sure all the moving parts of your car, like cup holders, are tight and secure so they don’t shake.

Also, get rid of any loose items, like keys and cell phones, from your dashboard.

When and after insulating your car, make sure you don’t leave any gaps.


How well do the soundproofing methods work?

First, it will make strange things happen, but it does work. How well you can block out noise depends on the methods you use. Also, the level of noise reduction depends on the type of car you are using. Older models are harder to soundproof.

In short, these tips may not get rid of all the noise in your car, but they do make it quieter and more comfortable.


How much can you weigh on the Onewheel XR and Pint?

Why are electric skateboards’ weight limits and maximum loads so important?

I’m going to tell you a story…

When I bought my first electric skateboard, I chose this mini-style one for $250 from Amazon. It had an overall rating of 3/5 stars and said it could go 12 mph for 7 miles, so I figured why not give it a try? I’ll use it to get to and from school and the train station.

I didn’t pay much attention to how much weight the board could hold or to the other specs… (Big mistake).

When I first got the board, I was so eager to try it out that I ran outside to see if it worked. When I got there, I saw that everything I had bought was a waste.

When I jumped on the board and tried to move forward, it didn’t move much… I tried again, but it moved as slowly as a snail. Don’t forget that this happened on a perfectly flat surface!

The motor was so weak, and the weight limit was a lot less than what I weighed. I gave up and sent the board back for a refund, wasting my time…

Lesson learned!

Make sure you know how much an electric skateboard or other mobility device can hold before you buy it so you don’t slow it down!

Same thing with the Onewheel…

So, how much can you weigh?

The maximum weight for both the Onewheel XR and the Pint is 275 lbs (125kg).

Most boards have a weight limit of between 180 and 350 pounds, so this is on the higher end of what you can carry.

If you still weigh more than 275 pounds, you should look for a board with a higher max load capacity. In fact, you shouldn’t use the Onewheel if you weigh even a little bit more than 275 pounds.

I think you should be under 250 pounds to avoid poor performance.

What will it be like to ride if I’m on the heavier side?

Here are the current specs for how well the Onewheel XR works:

  • Top Speed: 19 mph
  • Range: 12-18 mile range
  • Incline: Around 20%

For the Pint the performance is slightly inferior:

  • Top Speed: 16 mph
  • Range: 6-8 miles
  • Incline: Around 20%

But if you’re on the heavier side of the 275-pound limit, you can expect these numbers to drop sharply.

When you add more weight to a skateboard, gravity pulls down harder on it. This causes more friction between the board and its wheel. When there is more friction, the motor has to work harder, which uses up the battery much more quickly.

Your range will be cut down by a lot, and your top speed may be 5 mph slower. On the slower and smaller Pint, this won’t make much of a difference…

What are some boards that can hold more weight?

If you’re concerned about the weight limit, here’s a list of a few boards that will certainly fit almost anyone of any size:

  • Aeboard AT2 – 330 lbs (150 kg)
  • Aeboard GT – 330 lbs (150 kg)
  • Bajabord G4 – 350 lbs (160 kg)
  • Bajaboard S2 – 350 lbs (160 kg)
  • 350 lbs Lacroix Jaws (160 kg)
  • Lacroix Nazaré (Lonestar) – 350 lbs (160 kg)
  • Meepo V3 – 300 lbs (136 kg)
  • Meepo NLS Pro – 300 lbs (136 kg)
  • Meepo City Rider: 300 lb (136 kg)


What Size Spark Plug Socket For Lawn Mowers?

Lawn mowers are common tools that a lot of us use to maintain the neat appearance of our lawns and keep them trimmed. You might be wondering what size spark plug socket to buy if you are in the market for a new lawn mower or if your spark plug is about to give up the ghost.
By providing responses to a few questions regarding the different kinds of spark plugs that are utilized in lawn mowers, this post will assist you in determining what size spark plug socket you need to purchase for lawn mowers.

What size plug is used in a lawn mower?

For the most part, lawn mowers have a two-pin plug. Other machines, such as gas mowers and chain saws, often use a three-pin socket for their plugs.
An extra-large plug socket can be found on lawn mowers with larger-than-average panels. In addition, if you’re in the market for a new lawn mower, be sure to purchase the correct size plug socket.
Exactly what is the diameter of a typical lawn mower’s power socket? For each model of lawn mower, there is a specific size of spark plug socket that must match the machine’s actual spark plug. When it comes to two-pin machines, you’ll need to make sure they fit into your new mower’s two-pin socket.

What type of spark plug socket should I use to replace my lawn mower’s plug?

The spark plugs in your lawn mower are an essential component of the machine. When you ride your lawn mower, you will frequently hear a squeal because the spark plug is responsible for igniting the fuel. When you are finished mowing, the machine needs to be taken apart and cleaned so that any dirt that may have been kicked up doesn’t make its way into the fuel line.
It’s possible that you’d rather avoid the task of disassembling the lawn mower, but if you want to prevent an electrical accident, you’ll need a spark plug socket that’s simple to take apart and put back together again after it’s been cleaned. It is also essential that the plug of the socket is compatible with the plug of your lawn mower, which will typically have a size of 1/4 inch. The following is a table that contains common lawn mower plugs, along with the sizes and plugs that correspond to each type of plug.

Which plugs are compatible with a lawn mower?

Spark plugs come in a wide variety of designs, each with its own set of pros and cons. A lawn mower is equipped with a spark plug, and we explain how to identify which are compatible and which are not.
What lawn mower plugs are available? Spark plugs come in a variety of shapes and sizes. Type 1 spark plugs, also known as Ballpeens, are the most common. Small gasoline engines, lighters, and lawnmowers are all good candidates for this spark plug.
However, they will not work with a propane or DC mower, as these models do not use a spark plug to start the engine.

What other tools do I need for changing a spark plug on a lawnmower?

Long grass can be cut down with the help of a lawn mower. When it’s time to replace the spark plugs in your lawn mower, you’ll probably need to do the same thing. A spark plug socket is commonly found on lawn mowers.
Changing the spark plugs in your car, van, or motorcycle also necessitates changing the spark plugs. This article on how to check and replace your car’s spark plugs will help you if you own one of these vehicles and aren’t sure whether or not your spark plugs are in good working order.
Spark plug sockets come in a variety of sizes. When changing a lawn mower’s spark plug, you must use a socket of the correct size.

Why is the socket size important for lawn mowers?

The amount of spark a spark plug produces is directly proportional to the size of the socket it is installed in. The spark plug socket can be found in various places on lawn mowers, including the bottom, the front, or both (in the hood).
By answering the following questions, you can figure out what size socket your lawn mower needs. What role does the socket’s size play? An air gap is required between the spark plugs in a lawn mower engine.
Fuel mixes with air and is ignited by a spark plug when it’s working hard enough. In order to ensure the plug gets enough air, you should use a socket of the correct size.

How to remove and replace a spark plug in a lawn mower

It’s necessary to remove the spark plug from a lawn mower before inserting it into the fitting. An end-shaft hole accepts the spark plug, which is made of plastic. Most lawn mowers come with a large, round hole in the end of the blade.
In some cases, you may need to remove the fitting before installing a smaller diameter spark plug. Spark plugs are used to measure the plug’s diameter. There are a number of spark plugs that are placed in a circular fitting called a “spark plug socket.”
To identify the plug, the spark plug sockets come in different sizes and have different numbers attached to them. The first number indicates the plug’s diameter. This number is commonly written in this format. If you need to remove a number from a socket, where is it located?


To view the image in its full size, please click here. How do you determine the size of the spark plug socket to purchase for a lawn mower? You will need to take precautions to ensure that the spark plug you use in your lawn mower is appropriate for the kind of engine it has. There are three standard varieties of spark plugs, but none of these are suitable for use in all ignition systems.
Some lawnmowers are able to operate with a spark plug that has a stronger spark and higher compression, while others are able to operate with a spark plug that has a weaker spark and lower compression, and some lawnmowers are unable to operate with any type of spark plug at all.
If you want to purchase a spark plug for a lawn mower that is compatible with the engine in your mower, the first thing you will need to do is determine the type of spark plug that is used in your mower. When you purchase your spark plug from the manufacturer of your mower, they will let you know which model of engine it is designed to work with.

See more : Best lawn mowers for thick grass

Stereo Receiver Vs Integrated Amplifier: Which One Is The Best?

We are going to explain the differences between a stereo receiver and an integrated amplifier, as well as help you decide which of these two options is better for your needs. The stereo amplifier and the stereo receiver, both of which are commonly found as components of home audio systems, are two different types of devices. The receiver is the foundation of even the most fundamental types of stereo systems, whereas component systems add an amplifier and a preamplifier to the mix.

The electronics of the receiver are included in a single box rather than being housed in several separate units since the receiver is an integral part of the amplifier.

stereo vs. integrated amplifier

Comparing Amplifiers and Receivers! Everything that you absolutely must be aware of!

An audio line level signal is created by audio source components such as CD players. The purpose of a stereo amplifier is to carry this signal, boost its power while preserving its frequency, and then carry it to an output.

The strongest signal that is created by the amplifier is capable of driving the speakers and making sound. On the other hand, a line-level signal is unable to perform either of these things.

A stereo component known as a receiver is a device that combines an amplifier, a preamplifier, and a radio tuner into a single unit. It is a more cost-effective method of getting all of the essential elements that must be included in a stereo system.

stereo receiver vs. integrated amplifier Pros and cons

It is common knowledge that the finest performance and quality may be attained by purchasing a preamp and amplifier from separate vendors. Separate components also provide additional versatility when it comes to repairing and improving particular areas of the stereo system. However, acquiring the components separately will result in higher overall costs and a larger storage footprint.

Advantages and disadvantages for the recipient: It is possible to achieve a lower total cost and a more user-friendly assembly by basing a stereo system on a receiver. On the other hand, if just one component of the receiver stops working, it is essential to fix the whole thing. There is a possibility that the sound will not have the same high quality that you hear when using the components.

Stereo receiver vs. integrated amplifier considerations

Both an amplifier and a receiver can be combined into a single component if desired. The receiver is capable of acting as a preamplifier and can feed audio at line level to the amplifier so that it can be amplified. A set of RCA cables can be utilized to achieve the desired connection.


It is common practice to limit the meaning of the term “components” to the aforementioned pieces of apparatus; but, in order to present an accurate picture of the situation, we will also take into account the speakers. The speakers are the portion of the stereo system that are the most noticeable and audible to the user. In most cases, they will make use of an electromagnetic driver or a series of conductors in order to transform the electrical signal that is being transmitted from the amplifier into waves that can be heard.


The ability of your speakers to reproduce low frequencies is enhanced by the use of subwoofers. The vast majority of speakers are unable to produce the lowest possible bass, however subwoofers are designed with particularly massive drivers to address this deficiency. There are two types of subwoofers: powered and passive.

The main difference between stereo receiver vs integrated amplifier

A stereo receiver is an essential component that not only has a preamplifier and amplifier contained within a housing, but also a radio tuner for the purpose of receiving radio signals. An integrated amplifier typically consists of an amplifier as well as a preamp, although it typically does not have a tuner.

Choose the receiver because from this with the control you will be able to manage the volume because if you catch the ample, the volume will have to be controlled from the source you connect to it or manually. The receiver will have a radio tuner, and the amplifier will work more similarly as if you were using a power stage to mount the equipment in several modules.


How to Grip Tape a Skateboard or Longboard?

Griptape is the rough layer on the bottom of a skateboard deck that makes it easier for your shoes to stick to the board. You can either take your board to a skate shop or do it yourself. Replacing your grip tape makes you safer and helps you get better, so heavy skaters should do it often.

Getting prepare for the Board: 

  • Buy grip tape
  • Put your skateboard on a clean, flat surface to work on.
  • Use a Stanley Knife blade to cut off any grip tape that is already there.
  • a hairdryer or a heat gun
  • Give your skateboard a full clean.

Putting up tape

1.Place the grip tape in the middle of the skateboard deck.

Start by lining up the tape with the board. This way, you’ll know how long it needs to be and it won’t be stuck on wrong. Once a mistake sticks, it’s hard to fix it. Make sure the grip surface is longer and wider than your deck. You will cut off the extra tape when you’re done. If your grip has a design, move it to where you want it.

Some people don’t like the “classic” grip, so they choose other ways to hold the object. For example, you can cut your grip in half before attaching it so that you have a line of grip-less space across your board, or you can draw a “silhouette” and cut it out so that you have an icon on your board.

Imagine that the middle of your grip tape has a drawing or design, and you don’t want it in the middle of your board. Just put the drawing in the middle of where you want it (e.g. the nose or the tail). You’ll probably have a part of your deck with no grip, but you’ll also have a big piece of grip hanging off the other side. Cut out this piece and use it to make up for the “missing grip area.”

2.Peel the paper guard back a few inches and put it on one end of the board.

Smooth out any small bubbles by pressing and pushing in the direction that the tape is going. If there are big bubbles that could cause a crease, you will need to very carefully pull back on the grip tape to get rid of them. Make sure the glue doesn’t stick to other things.

Use both hands. This takes time and patience, because you don’t want to rip the tape.

3.Smooth the whole grip onto the deck with care.

Start slowly at one end of the board and work your way across, pressing down on the tape to get rid of any air bubbles. Some brands of griptape already have small holes in them to prevent air bubbles, but you should probably flatten it anyway. Put the grip tape flat against the board’s edges.

You can pull the grip tape up and try again any time. If you do this more than once or twice, the grip tape might lose its stickiness.

4.Make sure the grip is in the right place on the board.

Make sure the griptape covers the whole surface, unless you want the wood to show in some places for style. Some of the griptape may go past the edges of the deck, but don’t worry—you can cut off the extra with a knife or razor.

Completing the Board

1. Clean the edges.

You’ll notice that the edges of the deck give you “extra” grip. Use a screwdriver, a metal file, or something else with a flat edge to scrape along the board’s edges until the griptape gets a white edge. This is how you can seal the griptape’s edges. If you do this right, your grip will have a white outline of your deck. This outline shows you where to cut off the extra grip tape on the side of your skateboard.

Make sure to use long strokes instead of short, aggressive ones, or you might tear up the sides. Also, be careful not to remove the shine from the edge of your board by filing it.

2.Cut off any extra tape with a knife or a box cutter.

As a result of sanding, the edges of most boards are curved, so you should cut the tape past the curve along the edge. For the best result, make cuts that are slow and steady. Remember to hold the blade at a slight angle toward the edge of the skateboard so you don’t get a small line of grip sticking out. Use the outline of your grip as a guide: you need to cut along the sides of the deck and around the nose and tail of the board.

Make sure that your fingers are always out of the way, as the razor blade can easily slip out of the material.

It will be easier if you use both hands. You don’t want it to dig into the deck of your board by accident.

3.Flatten out air bubbles.

Once all the tape is on the board, check for small air bubbles. Cut small holes in the grip tape with a knife or razor blade. This should get rid of any bulging air bubbles. Smooth over the cut so the grip tape will stick to the deck easily.

4.Make holes so the trucks can be screwed on.

If your skateboard doesn’t have trucks yet, use a screwdriver to make eight holes in the griptape where the trucks’ screws will go. If you already have trucks on your board, you can wait to poke these holes until you replace the trucks, or you can poke the holes this way:

Take a second deck of the same size with no trucks on it and use it as a “guide” for where to poke the holes. Use a pencil to mark the spots or make a small hole. Now you can use a razor blade to cut a big enough hole around the screw to unscrew the trucks. Take each one off and put it back on to make it look “cleaner.”

Try to guess where the holes go if you don’t have a second board. Try putting a needle in and “following” the screws. If you poke the needle in the middle of the deck, it won’t move very far. If you poke the screw, the needle will move further, showing you where the hole needs to be.

5.Make the edges look nice.

Your first try might look a bit messed up, so go around and smooth out the bumps. Run the Stanley knife, box cutter, or razor blade along the outside edge of your skateboard to get rid of any extra pieces. As the deck gets older, most of the flaws will become less noticeable. Take a small piece of extra grip or sandpaper and lightly rub the edges where the grip is stuck to the board. This might keep the grip from coming off the board in the future.

6. Add any last-minute touches of style.

While you have the knife out, you can cut a small triangle or other shape between the screw holes on one end of the board. Some skaters do this so they can tell which end of their board is the front or back. Cut a circle or a hexagon out of your board to make it look different and give it interesting ways to ride. If you want, you can draw designs or patterns on the grip tape with paint markers or colored Sharpies. Try new things!


How to go faster on a longboard?

Skateboarders find it more fun and thrilling to go fast on their boards. So, you might be upset that skateboarding doesn’t make you feel like that.

Don’t worry, you can make your skateboard go faster in two ways: by pushing and by pumping. Also, the speed of your skateboard depends on a number of things. These are having your feet in the right place, having enough power as you push harder, and making sure your equipment is in good shape.

Here is a detailed explanation of how to push a skateboard faster.

How to Push Faster?

To go fast on a skateboard, you have to learn the right tricks and how to stand on it. When skateboarding on flat ground, the most common way to go faster is to push off with one foot. If you want your skateboard to go as fast as you want it to, you have to push as hard as you can.


Step 1: Kicking and advancing

  • Place your front foot on the front of the skateboard deck to start.
  • Put the weight of your body on your front foot.
  • Kick as far forward as you can with your back foot.
  • Your legs are bent at the knees, and your toes are pointed down.
  • Your two front wheels should land after your toes.

Then kick it back up as hard as you can, making sure to pass the two wheels at the back of the skateboard. Slide your front hand backward and your back hand forward at the same time.

How fast your skateboard goes depends on how hard you push and how long your toes stay on the ground. As you push off the ground, your back foot will give you the speed you need and also control the movement.

How you move your feet is a big part of making your skateboard go faster. The harder you push and the more force you put into it, the faster you will go. As you learn the right way to push harder and faster, you’ll need to coordinate the movements of your upper body while riding a board to keep your balance and momentum.

Step 2: Pumping to get going faster

On flat surfaces, you should push, but on curved surfaces, you should pump.

Pumping on a skateboard is similar to pumping on a swing. To make the swing go higher, you have to lift your legs and put them back down when you’re at the top.

  • Make your knees bend.
  • As you skate toward the more flat bottom of the curves, your upper body should be facing forward and down.
  • As you transition, straighten your legs as you rise.
  • From this position, you can go as fast as you want.
  • The higher you can fly over the edge, the faster you are going.

How to Make Your Skateboard Go Faster in Other Ways

In general, it’s important to learn the right way to push and pump to speed up your skateboard. But you can also speed up by making sure your gear is in good shape.

Technically, the wheels on your skateboard have something to do with how fast or slow it can go. You should think about getting new wheels because size and quality are important.

Even though smaller wheels are easier to move and get going faster, bigger wheels will give you the most speed. Not only are they great for cruising, but they also tend to roll a little longer and give you more speed.

High-quality urethane skateboard wheels tend to roll faster and last longer. You can also make your skateboard go faster by getting bigger, harder, and better wheels.


If you want to go faster on a skateboard, you need to learn how to push faster. To get the speed you want, you need to use the right techniques and tricks.

But it’s not good to have too much of anything. As the speed goes up, you have to take more care and safety measures when you do your skateboarding tricks.

Which do you prefer? Pushing or pumping? Leave a comment below and tell us what you think. Have fun and stay safe!


What Is IPS Glow And How Can I Reduce It

There are a lot of things you need to know about a display in order to get the best results. But every now and then, we run into problems or display errors that require the user’s attention. You can easily solve the problem, but the key is to know what to do.

IPS glow is one of the most common things that makes the view immediately worse. And if you’re a graphic designer who uses Adobe Photoshop or Illustrator, the IPS glow can be a bothersome bug. But it’s pretty normal, and you don’t need to worry about it because it’s easy to get rid of.

If that IPS glow is showing up on your display monitor, you will want to get rid of it. In this article, we will only talk about what an IPS glow is and how to get rid of it as much as possible. Read on to find out more!

What’s IPS Glow?

If you have an IPS (In-Plane Switching) display monitor, you may have noticed a glow around the edges of the screen. It shows up especially when the image and object on the screen are a little darker. For example, if you are sitting in a dark room, the IPS glow will make the screen look milky white and glow. Definitely, that hurts the image quality and makes it harder for the site to pick out better and more accurate details. For professional users, this is the biggest problem.

How to make the IPS glow less?

It’s not a big deal to cut down on the IPS glow. But you should always check to make sure that the display you buy doesn’t have this problem. If your IPS screen has a medium amount of glow, you can get rid of it by:

1.Making the light less bright

If your computer monitor already has this IPS glow problem, you will see the glow if you use the monitor at full brightness and have a dark background on the screen. One way to get rid of that glow, though, is to turn down the brightness to a certain level. This will change the IPS glow right away, and you will notice the change right away.

But you can turn up the brightness if you are not sitting in a dark room or a place with a lot of haze around you. For example, if you are in a room with a lot of light or where the sun is easy to get to, you may need to turn up the brightness of the screen.

2.Change the angles and sit a little further away

If you’re having trouble seeing or seeing things from the right angle, the easiest thing to do at first should be to change how you’re sitting. Keeping the angle well-adjusted is another easy way to cut down on IPS screen glow.

Tilt the screen slightly and change the height of the monitor from where it is now. This will definitely make a difference for the display, and you’ll notice the IPS glow going away right away.

Also, watch how far away you are from the table and how you are sitting. Many professional users and gamers have said that sitting farther away not only makes the IPS glow less noticeable, but it also helps your eyes.

Also, if you set the angles for how you sit, that will help you even more. Some of the IPS glow will go away if you move back a little bit from the screen.

4.Keep the light source going

After you’ve made these two simple changes, you can also add a source of background light to your sitting area. Also, the glow on the screen is all about how the light hits it from different angles. Now it’s time to pay attention to the light in your room. You’ve already checked the brightness and set the angles. If you put the lamp next to the computer screen or use RGB lighting in general, it will be pretty useful. If the room or area where you use the monitor already has enough light, IPS glow is less likely to happen.

4.Try to think outside the box

While you try everything you can think of to get rid of the IPS glow, why not use something that comes in handy? Just get a nice, clean piece of microfiber cloth and gently rub the monitor screen and its edges. Do that for another twenty to thirty minutes and see what happens.

Even though experts wouldn’t recommend it, many users say it works well. So, if you keep that in mind, you can try it.

5.Loosen the design of the frame

Compared to the solution above, losing the display is a bit worse and requires more careful hands. Also, make sure you don’t use your valuable credit cards while you’re losing the display panel. If you’re lucky, losing may help you in some way, but it’s not a 100% real way to get rid of glow when switching planes.

It goes without saying that each display panel is built in a different way. So be careful and don’t do any more damage that you can’t fix. For example, you might like the backlight bleed but want to get rid of the IPS glow. To do this, you need to search in the right way.


What’s the difference between backlit bleeding and the IPS glow?

People often get IPS glow and backlit bleeding on a display screen mixed up. But there are two things that are completely different. You already know that an IPS glow is when the white edges of a screen light up. If you’re in a dark room or seeing a dark image on the screen, the glow will show up, which also makes the display screen less perfect. Depending on what kind of monitor you have, the brightness and angle may be different.

Backlit bleeding, on the other hand, is when the light source comes from behind. When the LCD doesn’t need the light, it blocks it, making the screen dark and black. If it doesn’t block the light well enough or doesn’t do it at all, the light leaks through the screen, which is called “backlit bleeding.”

How do I know if the IPS glow is on my display monitor screen?

Before buying the monitor, you should look at its parts, features, and how well it works. When it comes to the screen, one of the most important things is that the IPS glows.

To test that, put the monitor (which should be turned on) in a dark room with very little or no other light. Make sure to keep it as dark as you can so that light from the sun, a lamp or bulb, etc., can’t get in. This is because the IPS glow will show up more clearly in a dark, opaque room.

Why do I have to look at the IPS glow?

If you have IPS glow, you might want to know why it’s happening and what’s causing it. It’s a good thing that it’s not a big problem, and as you’ve seen, there are many ways to cut it down.

But to get back to why it happens, it’s a bug that happens by default, and the only way to fix it is to make sure it’s made right. But if you have an IPS display, the glow is almost certain to happen.

The display screen panel has several layers, such as a coating that prevents glare and a layer housing. The light is likely to shine on the background instead of through it. During this process, the extra light goes through the screen of your display, which is what causes IPS glow in the end.

Is it normal or bad for IPS to glow?

If you’re worried about the IPS glow, you should know that it’s pretty common, especially on an IPS display. Even though it isn’t very dangerous, it does make the viewing angle less accurate and perfect. If you are a gamer, this can make it hard to play smoothly. Every owner of an IPS screen seems to ask about IPS glow and how to get rid of it, so you don’t have to worry about it as long as you’re doing something to get rid of it.

One Last Thing

IPS glow is nothing to worry about. Also, there are many ways to cut it down, like buying a new display monitor or getting rid of your old one.

In this article, we talked about tips and some of the most frequently asked questions about the IPS glow. We have done research and thought about the topic in order to give you the best content that is true.

It will definitely help you and save you the trouble of having to return it later. It is hoped that this information will be helpful and right. But you should always test the screen before you buy a monitor.

How Much Does it Cost to Build A PC Right Now?

Building your own computer? Need a PC cost breakdown? This article covers the expenses of constructing your own PC to help you budget.
There are two sorts of computers: productivity and gaming. How much a computer system costs depends on the sort of computer you require.
This article doesn’t address productivity systems. In part, this is because If you operate in a sector that requires high-end CPUs and other components, you should create your own system. In certain use situations, “larger is better,” placing the typical cost of such systems beyond someone who doesn’t earn a career off a computer workstation.

Gaming PC components include:

1. GPU (Abbreviated as GPU)
2. CPU (Abbreviated as CPU)
3. Motherboard
4.RAM (Abbreviated as RAM)
5. SSD/HDD Storage (HDD)
6. UPS (PSU)
7. Case
8.CPU cooler fans
10. Peripherals
Because they’re the most crucial parts of a system, the GPU and CPU take up most of the cash. Together, they’re responsible for nearly every process that a modern computer is responsible for handling, making them the focus of this article.
Together, they’re responsible for nearly every process that a modern computer is responsible for handling, making them the focus of this article.

1. Graphics Card (GPU)

The Graphics Card is frequently the most costly component. This is especially true now. I highlighted a “worrying pattern.” This tendency affects GPUs.
NVIDIA and Ryzen both just introduced their top-tier Graphics Cards. There’s little incentive to acquire a different Graphics Card. What’s wrong?
Some. The COVID-19 epidemic has caused a worldwide chip scarcity, which has affected GPUs. With the current crypto mining frenzy, where people benefit from owning and buying Graphics Cards in bulk, the GPU market has been flipped upside down.
The $700 3080 is currently advertised for $1,500 on Amazon. The $600 3070 is now $1,100 on Amazon. Even four-year-old cards have been selling for more than their original price.
Unless you get a card from NVIDIA, you’ll spend more. This assuming the cards are in stock; fresh batches sell out quickly. So, what’s next?
A reseller is an option. Hopefully, you’ll pay the same. When feasible, hardware enthusiasts purchase in quantity to avoid scalpers. The surplus cards will be resold at a low to no markup. Some nice person will sell the card at its original retail price, but these folks are the exception rather than the rule.
If you’re prepared to sacrifice performance, try the aftermarket. You don’t always require top-of-the-line gear. 2D platforming games work nicely on older GPUs, for example. Sometimes you don’t need a GPU (more on that later).
Graphics card price? Graphics cards cost $200 to $3,500. Normal market figures would be lower.

2. Central Processing Unit (CPU)

In fact, the kind of CPU in a system often dictates what that system’s ultimate function is. The CPU executes most of a system’s processes, and various CPUs have distinct tasks.
In rare cases, a CPU may even replace a GPU. CPUs with integrated graphics (abbreviated as iGPU). If you only want to browse the web, don’t get a ‘standard’ CPU. Depending on the game, the integrated GPU may frequently provide a good gaming experience. A CPU with an iGPU may cost as low as $100 for online browsing, while one that can run games costs $250.
If you’re searching for a gaming CPU (with a GPU), the 5600x starts at $300 USD. Prices peak about $900. To prevent bottlenecking your GPU and saving money, examine how powerful your CPU needs to be.
CPU price: A CPU may cost between $100 and $900.

3. Motherboard (MOBO)

A computer won’t operate without a motherboard. It distributes electricity and connects PC components.
Make sure your motherboard works with the other parts.
Ensure your motherboard and CPU are compatible. Most other components are globally compatible.
Depending on the board you choose, update the BIOS. It’s straightforward, however you may buy a suitable motherboard without updating.
Compatible motherboards cost $125 if you can upgrade the BIOS. Most of these motherboards’ final upgrade cycle is now, thus if you update your CPU later, you may need a new motherboard. A future-proof motherboard costs $200-$300.
Motherboard price: A motherboard should cost between $120 and $300.

4. RAM 

RAM capacity and speed are measured (clocked in mHz). More RAM means more applications, and quicker RAM means faster processing. There are several configurations. Important ones are below.
1/8: 8GB; 2/8: 16GB; 2/16: 32GB; 4/8: 32GB; 4/16: 64GB
16GB of RAM is the current norm. 32GB is a premium for memory-intensive titles like Apex, Warzone, and Battlefield. 64GB is usually excessive. 8GB of RAM is fine for inexpensive computers since it’s simple to add more later. You should increase 8GB of RAM as soon as feasible.
RAM comes in sets of two or four, although 8GB sticks are available. Here’s the average cost.
18: $35; 28: $70; 216: $120-150; 48: $160; 416: $275
Four-pack RAM has greater clock speeds, therefore a higher unit price.
How much is PC RAM? Expect to pay $35-250 for RAM.

5. Solid State Drive (SSD) / Hard Disk Drive (HDD)

It may be perplexing to see two separate items mentioned here, however solid state drives and hard disk drives both perform the same purpose. Both SSDs and HDDs store data (including the system’s OS). In essence, an SSD saves data electrically whereas an HDD does it physically.
SSDs are generally quicker, quieter, more dependable, and have a longer lifetime than HDDs with the same—or even more—storage. SSDs are a “quality of life” non-essential. High-quality SSDs are inexpensive these days, therefore you should use one in your setup. Installing your operating system and games on an SSD reduces load times.
Most motherboards have numerous SATA ports for connecting multiple drives. This enables connecting an SSD and HDD viable.
The Seagate BarraCuda is popular. The 2TB model costs $50 on Amazon—sometimes less. Unless your job or hobbies need more, there’s no reason to go elsewhere. 4TB models cost $75 and 8TB models cost $150.
If you’re on a budget, an HDD is OK. If you have the money, consider it. Some SSD manufacturers have been ‘exposed’ for decreasing the write speeds of their SSDs, which isn’t the topic of this article. Consider paying extra for a reputed brand.
If you have extra cash, you may get a large SSD and skip the HDD. 2TB SSDs cost $200, while 4TB SSDs cost $400.
SSD and HDD prices? Your system’s storage might cost $50 or $450.

6. Power Supply (PSU)

Your build’s power supply has to be sized. OuterVision’s PSU calculator may help you choose the right size. 650-750 watts is often suggested to allow for future improvements.
If you can, acquire a completely modular power supply. It simplifies life.
Power supply price? Depending on wattage and efficiency, PSUs cost $60-$150. (as noted by its 80 Plus rating).

7. Case

Choosing a PC case is crucial. The case you chose will decide your system. Not all cases can fit all systems. Cases vary in size and may not fit your system’s essential components.
Some cases keep your system cooler than others. A PC case with greater ventilation will cost extra.
Cost of PC case? Budget $50 to $200.

8. CPU Cooler

This one is more difficult. Liquid and air-cooled CPU coolers are available. This article solely considers AIO and air coolers. Remember that some CPUs come with an air cooler; depending on your needs, it may be sufficient.
All-in-one coolers have liquid. Installing one has dangers.
CPU cooler price? AIOs cost $80 to $200. Expect to pay $45 to $100 for an air chiller.

9. Case Fans

Case-by-case fans vary. A computer casing may or may not have several fans. Cases may also house varying numbers and sizes of fans. Size, airflow, and RGB lighting affect fan pricing.
120mm fans cost $10, while 140mm RGB fans cost $20.
10. Other Peripherals
You’ll also need a monitor, keyboard, mouse, speakers, and a headset. As with components, peripherals have a broad range of performance.
Monitor costs range from $100 to the hundreds.
Keyboards, mouse, and headsets cost $20-$30 to $200-$300.

Example build

Below are links to guidelines with budget-specific component lists. These systems cannot be constructed at the mentioned prices at this time. Due to worldwide supply chain challenges and chip shortages, GPUs and other critical PC components are much more expensive than usual.
Now is still a good time to buy a prebuilt system. Prebuilt and bespoke gaming PC firms may still acquire graphics cards in bulk for close to MSRP. While we generally advocate constructing your own PC to save money, right now it’s better to buy a prebuilt machine.
So we’ve included several prebuilt gaming PC alternatives below.


A PC’s cost relies on several factors. It’s rare to find two identical computer builds.
You can create a $300 internet-browsing PC. $1000 is an excellent starting point for a budget gaming PC setup. Anything in between might range from $400 to $4000 or more. The user decides.